Examcrazy Logo
HOME  SITEMAP CONTACT US LOGIN
HOME Engineering AIEEE GATE IES DRDO-SET BSNL-JTO
MBA in India CAT How to Prepare for Exams Technical Freshers Jobs
  Follow us|  twitter  Orkut  facebook
BJT Tutorials
   Bipolar Junction Transistor- NPN
   Bipolar Junction Transistor- PNP
   DC Analysis of BJT Circuits
   The BJT as a Signal Amplifier
   BJT Small-Signal Equivalent Circuit Models
   BJT Small-Signal Amplifier
   Graphical Analysis of a BJT Small-Signal Amplifier
   BJT Biasing - Current Mirror
   Common Emitter Amplifier
   Common Base Amplifier
   Common Collector (Emitter Follower) Amplifier
   BJT Internal Capacitances. High Frequency Circuit Model
Free Electronics Tutorials
   Diode Tutorials
   BJT Tutorials
   MOSFET Tutorials
   Electronics II Tutorials
   Applied Electromagnetics Tutorials
   Microwave Tutorials
GATE preparation tips
   GATE Books & How to prepare
   Objective Solving Tricks
   Other GATE links
   IES exam preparation
   All about DRDO-SET
More Engineering Links
   Directory of coaching Institutes
   Govt engg college rankings
   Private engg college rankings
   Admission notifications for Mtech/PhD
   All Engineering Colleges in India
BJT Internal Capacitances High Frequency Circuit Model

The BJT amplifiers we have examined so far are all low frequency amplifiers. For large valued DC blocking capacitors and for frequencies of tens to hundreds of kHz, the simple smallsignal models we used will work well. As the frequency increases, though, there are multiple sources of effects that will limit the performance of these amplifiers including:
1. Internal capacitances of th BJT. These are due to charge storage effects at and near the two pn junctions.
2. Parasitic effects. These are due to packaging and transistor construction that create additional capacitances, lead inductances, and resistances. Additionally, the performance of many BJT amplifiers weve already examined will be sharply curtailed by DC blocking capacitors that have finite value (i.e., less than infinity). For these reasons, all real transistor amplifiers operate effectively only over a limited (but hopefully large) range of signal frequencies. Referring to Fig. 5.71(b), our analysis of small-signal BJT amplifiers up to this point has focused on the Midband frequency region. This frequency band is bounded by the frequencies fL and fH, which are the -3-dB gain frequencies, or half-power frequencies.

The roll off in gain near fL and lower is due to effects of the DC blocking capacitors CC1 and CC2, and the bypass capacitor CE. Its not possible to eliminate this effect, though fL can be moved about by choosing different values for these capacitors. Butlarge capacitors take up lots of space and can be expensive. The primary focus of this lecture, however, is the origin of the roll off in gain xperienced at higher frequencies near fH and higher.
Capacitance of pn Junctions
There are basically two types of capacitances associated with pn junctions:
1. Junction capacitance. This is related to the space charge that exists in the depletion region of the pn junction.
2. Diffusion capacitance, or charge storage capacitance. This is a new phenomenon we havent yet considered in this course. The junction capacitance effect was briefly mentioned earlier in this course in Lecture 4. The width of the depletion region will change depending on the applied voltage and whether the junction is reversed or forward biased:

The time-varying E due to the space charge in the depletion region is a so-called displacement current that can be modeled by a junction capacitance. The second basic type of capacitance, diffusion capacitance, is associated with pn junctions that are forward biased.

In this state, current will flow across the junction, of course. Because of the current source in Fig. 3.49 and the voltage dropV, holes are injected a cross the junction into the n region while electrons are injected across the junction into the p region.

The concentrations of these electrons and holes decrease in value away from the junction, as shown in Fig. 3.50, due to recombination effects.
The important point here is that these concentrations of charges create an electric field across the pn junction that will vary with time when a signal source is connected to this device. This electric field is directed from the n to p region, and the overall effect can be modeled by what is called the charge storage capacitance, or diffusion capacitance.
To summarize, the capacitive effects of a reversed biased pn junction are described by the junction capacitance while those of a forward biased pn junction are described by both a junction and a diffusion capacitance. In the latter case, though, the diffusion capacitance usually dominates.
BJT High Frequency Small-Signal Model
The active mode BJT has one forward biased pn junction (the EBJ) and one reversed biased pn junction (the CBJ). In the case of an npn BJT the capacitances associated with the pn junctions in the device are labe ed as:

As we just discussed, there is a junction capacitance associated with the reversed biased CBJ, which is labeled C as shown above. There will be a junction capacitance, Cje, associated with the forward biased EBJ as well as a diffusion capacitance abeled Cde. These latter tw o capacitances appear in parallel and so can be combined as Typically C ranges from a fraction of pF to a few pF while C ranges from a few pF to tens of pF, which is dominated by Cde. With these capacitances, the high frequency small-signal model of the BJT becomes

Note the use of the V notation in this small-signal model. Your textbook has switched to sinusoidal steady state notation for this high frequency discussion. The high frequency small-signal model in Fig. 5.67 also includes the resistance rx, which is mostly important at high frequencies. Its there to approximately model the resistance of the base region from the terminal to a point somewhere directly below the emitter:

C is sometimes referred to as Cob (or Cobo) in datasheets. This designation reflects the fact that C can be the output resistance when the BJT is used as a common base amplifier. The values of these small-signal circuit model elements may or may not be available in a datasheet for your transistor. For example, from the Motorola P2N2222A datasheet:

Actually, we would expect these capacitances to vary with the voltage across the respective pn junction. In the following figure from the Motorola P2N2222A datasheet, we see the dependence of Ceb (= C ?) and Ccb (= C ) for a range of junction voltages. (Perhaps t he labeled voltage for Ceb should be forward voltage?)

Unity-Gain Bandwidth
An important high frequency characteristic of transistors that is usually specified is the unity-gain bandwidth, fT. This is defined as the frequency at which the short-circuit current gain

has decreased to a value of one. A test circuit for this measurement would look something like:

The small-signal high frequency model of this test circuit is:

Applying KCL at the collector terminal provides an equation for the short-circuit collector current

At the input terminal B

Substituting (4) into (3) gives

Using the definition of hfe from (2) we find from this last equation that

It turns out that C is typically quite small and for the purposes of determining the unity-gain bandwidth, gm is | | j C . for the frequencies of interest here. In other words, the frequency at which C is important relative to gm is much higher than what is of interest here. Consequently, from (5)

We can recognize this frequency response of hfe in (6) as that for a single pole low pass circuit:

b0=gmrp in this plot is the low frequency value of | hfe|, as weve used in the past [see eqn. (5.93)], while the 3-dB frequency of | hfe| is given by

The frequency at which hfe in (6) declines to a value of 1 is denoted by T, which we can determine from (6) to be

such that

Therefore


This unity-gain frequency fT (or bandwidth) is often specified on transistor datasheets. On page 8, for example, f r =300 MHz for the Motorola P2N2222A. Using (9), this fT can be used to determine C p+ C p for a particular DC bias current.
Lastly, the high frequency, hybrid-, small-signal model of Fig.5.67 is fairly accurate up to frequencies of about 0.2 fT.
Furthermore, at frequencies above 5f b to 10 f b, the effects of r are small compared to the impedance effects of C . Above that, rx becomes the only resistive part of the input impedance at high frequencies. Consequently, rx is a very important element of the small-signal model at these high frequencies, but much less so atlow frequencies.


Discuss about BJT here
   START NEW THREADS
Discussion Board for BJT
Discuss all your issues or difficulties on BJT
Thread / Thread Starter Last Post Replies Views
example of BJT small signal
I want do to this


Posted By :-
 socheat
Jul 1, 7:35:08 AM 0 8415
drdo previous papar
preparation for drdo


Posted By :-
 rinkumathur.1988
Oct 16, 2:00:04 PM 1 10034
FET
Its operation and manufacturing.


Posted By :-
 dharmendra608@yahoo.in
Apr 16, 6:54:20 PM 0 6496
diode
sssssssssssssssss


Posted By :-
 sunilkumarmishra88
Dec 2, 4:03:32 PM 0 7000

To start your new thread you must login here.
New user signup at ExamCrazy.com Exam Crazy
To reply/post a comment you need to login, Use your user name and password to login if you are already registered else register here

EXISTING USER LOGIN
(Members Login)
Username:
Password:
NEW USER REGISTERATION FORM
Login-Id
Email-ID
Password
Confirm-Password
Full-Name

  About us | Privacy Policy | Terms and Conditions | Contact us | Email: support@Examcrazy.com  
Copyright 2014 Extreme Testing House, India. All rights reserved.  1628